Then turn off the local hot and cold water supplies. During this repair, you may need to pull the washer away from the wall so you can more easily access the rear of the appliance. This should be the first thing you do before starting any appliance repair procedure. Unplug the washer and turn off the water supplies.įirst, unplug the washer.
#How to replace a dishwasher water inlet valve install#
Order replacement part #W10364988 for most Maytag washer models and follow these steps to install it. Over time, the solenoids can also fail and won’t distribute water correctly. But if the body cracks, water can leak throughout the machine. If it is not continuous, replace the part that is specific to your model.The water inlet valve assembly controls and distributes water to different dispensers in your Maytag washer. Replace the vent fan if the motor is not continuous or if there is an issue with its turning.įinally, the third reason why your dishwasher may not be drying properly is a defective heating element. You can also try turning the fan blade by hand to see if there is anything causing it to stick. To determine if your fan motor has failed, test the motor for continuity using a multimeter. If the vent is opening properly, then you will want to check the vent fan motor. If you find that the vent is not opening correctly, replace it with an exact replica. You will know that the dishwasher vent is the problem if the vent does not open properly. To fix this problem, you need to check the dishwasher vent and the motor. The reason why your dishwasher does not dry properly is dependent on how your model dries the dishes: either with a vent, vent motor, or heating mechanism. You will use a multimeter to see if there is an issue with the solenoids.įinally, the last common problem associated with Bosch dishwashers is that the dishwasher does not properly dry the dishes. The solenoids are magnets that allow the water inlet valve to open and close. You may also want to test the solenoids of the dishwasher. Reassemble your dishwasher and test to make sure it is fixed. Then, remove the old water inlet valve and replace it with the new one. You will need to detach a wire harness, disconnect the water line, and remove the brass elbow. You do this by removing the old valve, which is accessed by the lower access panels. To fix this problem, you can replace the water inlet valve. If the valve is defective, it can cause it to close early, which prevents water from fully filling up the dishwasher during the cycle. Like many of the other problems on this list, water not filling up the dishwasher is caused by a faulty water inlet valve. It is important to fix this problem right away. This is a problem since it will not allow the dishwasher to properly clean your dishes, which is unsanitary. The fourth common problem associated with Bosch dishwashers is that water does not fill up the dishwasher. It may take you a couple of tries before you are able to find the debris. This will allow you to see any debris that may be getting in your way. It is important to note that you should try to make the water backwasher through the impeller and rubber piece.
![how to replace a dishwasher water inlet valve how to replace a dishwasher water inlet valve](https://img.youtube.com/vi/VfCvT80e0hc/maxresdefault.jpg)
Remove any debris.Īdditionally, pull out the rubber check valve and make sure there is no debris. Move the impeller around to see if anything is jamming the impeller. Then, remove the part to reveal the impeller. Next, loosen and remove the nut using a screwdriver. Once most of the water is removed, place a dry rag all the way into the washer drain to remove all the water and junk.
![how to replace a dishwasher water inlet valve how to replace a dishwasher water inlet valve](https://removeandreplace.com/wp-content/uploads/2014/12/Dishwasher_Water_Inlet_Valve.jpg)
![how to replace a dishwasher water inlet valve how to replace a dishwasher water inlet valve](https://allthumbsdiy.com/wp-content/uploads/2017/01/allthumbsdiy-dishwasher-bosch-replace-water-inlet-valve-60-detach-water-supply-fl.jpg)
![how to replace a dishwasher water inlet valve how to replace a dishwasher water inlet valve](https://i5.walmartimages.com/asr/f21faf1d-fcd4-43d5-8216-3c438a13eaa1_1.3d15a9fb2260e4e764a3090a26e7b6b4.jpeg)
If there is a lot of water, you may need to remove the water by using a cup to ladle it out. Luckily, this problem is easy to fix.īegin by removing the filter and drain. This is extremely unsanitary, which is why it is imperative to fix this problem immediately. When this happens, the dirty water is left at the bottom of your dishwasher. Another common problem associated with Bosch dishwashers is at the dishwasher does not drain properly.